一、常見問題及解決Frequently Asked Questions and Solutions
問題question 可能原因possible cause 解決方法solution
1. 風機不工作
Fan doesn't work
中間繼電器R201.2 損壞
Intermediate relay R201.2
damage
變頻器損壞
The inverter damaged
風機損壞
Damage of fan
更換R201.2
Replace R201.2
與公司聯系
Contact with company
與公司聯系
Contact with company
2、電加熱器不工作
Electric heater doesn't work
風機未啟動
Fan don't start
固態繼電器SSR201 損壞
Solid state relay SSR201
damage
電加熱器損壞
Damage of electric heater
啟動風機Start the fan
更換固態繼電器SSR201
Replace the solid state r
elay SSR201
與公司聯系
Contact with company
3、空氣壓縮機不工作
Air compressor doesn't
work
中間繼電器R201.1 損壞
Intermediate relay R201.1
damage
空壓機未啟動
Air compressor is not st
arted
空壓機損壞
Air compressor damage
更換R201.1
Replace R201.1
啟動空壓機
Starting air press
與公司聯系
Contact with company
4、設備沒電
Equipment without
electricity
外加插座不可靠
Plus the socket is not
reliable
斷路器NFB 在關閉位置
Circuit breaker NFB in
closed position
檢查外接電源是否有電
Check the power converter
for electricity
把NFB 打開
Open NFB
5、HMI 觸摸屏無顯示工作
HMI touch screen no
面板啟動按鈕損壞
A button panel damage
更換啟動按鈕
Replace the start button
display 開關電源損壞
Switch power supply
damage
中間繼電器R1.2 損壞
Intermediate relay R1.2
damage
觸摸屏損壞
Touch screen is damaged
更換開關電源
Replace the switching
power supply
更換R1.2Replace the R1.
2
與公司聯系Contact with
company
7、進風溫度無顯示
Inlet air temperature
display
PT-100 溫度探頭連接松動
PT-100 Temperature probe
connection is loose
PT-100 損壞
PT-100 damage
PT 溫度模塊損壞
PT-100 Temperature module
damage
緊固
fastening
與公司聯系
Contact with company
與公司聯系
Contact with company
8、出風口溫度無顯示
Outlet temperature displa
y
PT-100 溫度探頭連接松動
PT-100 Temperature probe
connection is loose
PT-100 損壞
PT-100 damage
PT 溫度模塊損壞
PT-100 Temperature module
damage
緊固fastening
與公司聯系
Contact with company
與公司聯系
Contact with company
9、進風口溫度無法達到
設定值
Air inlet temperature
cannot reach the set value
風機風量太大
Fan air volume is too bi
g
修改風機參數
Modify the fan parameter
s
10.出風口溫度無法達到
設定值
Outlet temperature cannot
reach the set value
進風量太大（蠕動泵手動
時）
Into the air volume is to
o big (peristaltic pump m
anual)
修改蠕動泵參數
Modify the peristaltic pu
mp parameters
11.干燥室底端滴料
Drying chamber on the
bottom of the drop
進風溫度太低
The inlet air temperature is
too low
霧化空氣壓力太低
The atomizing air pressur
e is too low
壓縮空氣漏氣
Compressed air leak
進料量太大
增加進風溫度Increase the
inlet air temperature
打開設備后蓋板將壓力
調至2-3Bar（￠6 藍色氣
管）
Open the equipment
HouGaiBan dispatch
pressure to 2-3 bar ( ￠6
blue trachea)
Feed rate is too big 檢查各處連接是否漏氣
Check whether all
connection leak
修改蠕動泵參數
Modify the peristaltic pu
mp parameters
12.通針不工作
Needle don't work
空氣閥門未開
Air valve is not open
壓力太小
Pressure is too small
通針參數設定太大
Needle parameter setting
is too big
電磁閥損壞
Solenoid valve damage
打開閥門（￠4 白色氣管）
Open the valve (4 ￠white
trachea)
調大減壓閥壓力
Large pressure reducing
valve
修改通針參數
Modify the needle
parameters
等換電磁閥
Such as change of
electromagnetic valve
二、實驗準備The Prepare for Experiment
1.按照安裝說明將各部件安裝好
According to the installation instructions for the parts will be installed
2.按下設備藍色啟動按鈕，啟動風機，啟動加熱器
Press equipment blue button, start the blower, start the heater
3.設定進風溫度
Set the air inlet temperature value
4.待出風溫度達到設定值時，開啟蠕動泵自動
When the air outlet temperature reached setting value, open the peristaltic pump
automatically
5.先進水，觀察物料霧化及溫度變化情況，重新設定風機、進風溫度，待穩定后
進料
Import water firstly, and observe the change of materials and temperature, and r
eset the speed of the fan and the temperature of the air inlet , and import mat
erial after stable 。
停機步驟Stop Steps
1.當物料用完后，進水將膠管內的物料全部噴完后（約5 分鐘），關閉蠕動泵
When the material is used out, import water and spray all the material within the hose
(about 5 minutes), closes the peristaltic pump
2.關閉空壓機
Close the air compressor
3.關閉加熱器
Close the heater
4.待進風溫度降至40 度以下時，關閉風機
When the temperature of air inlet drop to 40 C°, close the fan
5.取下集料瓶，將物料轉移到其他容器中
Take the fixation material bottle down, transfer the material to other container
6.容器完全冷卻后取下清洗
When the container become to cool completely， take down and clean it。__